What this clip actually changes on your SHPOS Gen 3
The SHPOS Gen 3 Folder Deep Carry Pocket Clip is a replacement clip, not a full knife. The supplied product record states clearly: CLIP ONLY, DOES NOT INCLUDE BLADE. That matters before you order, because the clip is meant to replace the standard pocket clip on a folder you already own.
The clip is made from anodized aluminum and is ambidextrous, so it can serve left- or right-handed carry. The package includes a triangle insert and a screw to replace the standard pocket clip hole. You will need a number 8 torx driver for the screw.
Supplied clip details worth checking before you start
- SHPOS gen 3 Folder, Deep Carry Pocket Clip: CLIP ONLY, DOES NOT INCLUDE BLADE Confirms the purchase is a clip accessory, so you should already have a compatible SHPOS Gen 3 folder to mount it on.

SHPOS gen 3 Folder, Deep Carry Pocket Clip - SHPOS gen 3 Folder, Deep Carry Pocket Clip: Includes triangle insert and screw to replace standard pocket clip hole These are the parts you will work with during installation; confirm both are present before removing your existing clip.
- SHPOS gen 3 Folder, Deep Carry Pocket Clip: Anodized aluminum, number 8 torx, ambidextrous Tells you the driver size needed and that the clip can be set up for either hand.
Installing the deep carry clip: a supported sequence
The supplied evidence describes the parts included and the screw type, but it does not provide a full manufacturer procedure. Use the steps below as a conservative, evidence-based starting point, and stop if anything does not align with your folder.
- Confirm you have the right folder and parts: This clip is for the SHPOS Gen 3 Folder. Check that you have the clip, the triangle insert, and the screw. The record does not list additional hardware, so do not substitute parts unless you confirm fit separately.
- Remove the standard pocket clip: The clip is designed to replace the standard pocket clip hole. Use a number 8 torx driver on the existing screw. Keep the original screw and clip together in case you want to reverse the change later.
- Seat the triangle insert: The included triangle insert is intended to replace the standard pocket clip hole. Position it according to the hole pattern on your folder. The supplied information does not specify a torque value or thread-locking compound, so tighten conservatively and check for movement.
- Attach the clip with the included screw: Use the supplied screw and a number 8 torx driver. Because the clip is ambidextrous, decide on left- or right-side carry before final tightening. The record does not confirm a specific orientation, so test the clip position before fully snugging the screw.
- Check function before carrying: With the folder closed, confirm the clip sits securely and does not interfere with the blade path or pivot area. The record does not provide a carry-depth measurement, so judge deep carry by how the folder sits in your pocket.
Choosing clip placement for your carry style
The ambidextrous design means the same clip can be mounted for left- or right-hand carry, but the supplied record does not list specific mounting positions or a required orientation. Start with the side you normally carry on and check that the clip does not block your grip or sit under your palm when the folder is open.
Deep carry is a matter of how much of the folder sits below the pocket edge. Because the record does not give a clip length or carry-depth figure, the practical test is simple: clip the folder to your pocket, close the blade, and see whether the exposed portion feels secure and discreet for your usual clothing. If the clip feels loose or the folder shifts, recheck the screw and insert seating rather than bending the clip.
Fit checks and adjustment limits
The supplied information confirms the clip is for the SHPOS Gen 3 Folder and includes the triangle insert and screw for the standard pocket clip hole. It does not confirm compatibility with other models, so treat this as a model-specific accessory unless you can verify fit independently.
For adjustment, the record does not describe bending, tensioning, or a torque specification. Avoid guessing at those procedures. If the clip does not sit flush, remove it and check that the triangle insert is seated correctly and the screw is the included one. If the screw will not tighten properly, stop and seek guidance rather than forcing it.
What to check after installation
- Screw security: The included screw should hold the clip and insert in place. The record does not specify a thread-locking product, so check the screw periodically and after any heavy use.
- Insert alignment: The triangle insert is meant to replace the standard pocket clip hole. If the clip shifts, the insert may not be seated correctly.
- Carry side: The ambidextrous clip can be set up for either hand. Confirm the side you chose does not interfere with your grip or pocket draw.
- Blade clearance: With the blade closed, make sure the clip and screw do not contact the blade or block the pivot. The record does not include a clearance specification, so this is a visual and functional check.


