What the Hunter Skinner's materials mean for care
The Hunter Skinner pairs a grey and coyote G10 handle with a textured grip and an Armor Black Cerakote blade finish. G10 is a composite laminate, and the textured surface is what gives you control when your hands are wet or cold. Cerakote is a applied finish chosen for a low-reflective, tough surface. Neither material needs a complicated routine, but both benefit from a few consistent habits.
The supplied record confirms the handle material, the textured grip, the Cerakote blade finish, and Allen-bolt hardware. It does not include manufacturer cleaning instructions, torque values, or disassembly guidance. The steps below are general shop practices for G10 and Cerakote, not a restatement of a Half Face Blades procedure.
Hunter Skinner build details that shape the routine
- Hunter Skinner - Grey/Coyote G10, Armor Black Cerakote, Allen Bolts, Textured Grip: Handle constructed from grey and coyote G10 with a textured grip for improved control. The texture is the part that collects dirt and needs attention; smooth-polishing it away would change the grip you bought.

Hunter Skinner - Grey/Coyote G10, Armor Black Cerakote, Allen Bolts, Textured Grip - Hunter Skinner - Grey/Coyote G10, Armor Black Cerakote, Allen Bolts, Textured Grip: Blade finished in Armor Black Cerakote for a low-reflective, tough surface. Cerakote is a coating, so abrasive cleaners and hard scraping are the main things to avoid.
- Hunter Skinner - Grey/Coyote G10, Armor Black Cerakote, Allen Bolts, Textured Grip: Hardware includes Allen bolts for a secure and tidy assembly. You can check the bolts without guessing at a fastener type, but the record gives no torque spec, so snug-and-check is the safe approach.
A simple handle and blade care sequence
Work in this order so you are not moving grit from the blade onto the grip or the other way around.
- Start dry: Brush loose dust and dried debris out of the textured G10 with a soft brush before introducing any moisture. This keeps grit from being pushed deeper into the texture.
- Wipe the blade first: Use a soft, damp cloth on the Cerakote blade, then dry it immediately. Avoid abrasive pads and scouring cleaners, which can dull the finish.
- Clean the G10 grip: A damp cloth with mild soap is enough for the grey/coyote G10. Work along the texture rather than scrubbing hard across it, then wipe dry.
- Dry completely: Let the knife air-dry fully before storage, paying attention to the textured areas and around the Allen bolts where moisture can sit.
- Check the Allen bolts: Confirm the bolts are snug. The supplied record does not list a torque value, so check for looseness rather than forcing them tight.
Grip maintenance habits that protect the texture
- Keep solvents off the G10: Harsh solvents and strong cleaners are unnecessary on a G10 handle and can dry or dull the surface. Mild soap and water cover normal cleaning.
- Do not sand or polish the texture: The textured grip is a handling feature. Sanding it smooth trades control for appearance, and the supplied record gives no refinishing guidance.
- Store dry and separate: A dry sheath or safe keeps moisture and grit away from both the G10 and the Cerakote blade between uses.
- Recheck after wet use: After rain, blood, or a wash-down, dry the grip and blade and recheck the Allen bolts before the knife goes back into storage.
Where the supplied information stops
The record does not confirm whether the Hunter Skinner is dishwasher-safe, what specific cleaners Half Face Blades recommends, or what torque the Allen bolts should be set to. Treat any strong claim about those points as unverified. If you need a manufacturer-specific procedure, check the documentation that came with your knife rather than relying on general advice.
For most owners, the routine above is enough: dry first, clean gently, dry fully, and keep the bolts snug. The grey/coyote G10 and Armor Black Cerakote are durable materials, and consistent simple care will keep the textured grip doing its job.


